Tiếng Việt
中文 (中国)Kadier Floor Coating Product Range
Kadier has manufactured epoxy floor coatings and auxiliary materials for more than 10 years — from primers and intermediate coats to finishing topcoats for factories, warehouses, cleanrooms, basements and sports courts. Figures on this page are Kadier's official technical data (TDS); the system build for each project is confirmed after an on-site substrate survey.
12 product lines
Select a product to view its features, applications, application guide and technical data.
- Epoxy Primer
- Epoxy Intermediate Coat (tintable)
- Anti-Static Epoxy Intermediate Coat
- Roller-Applied Epoxy Topcoat
- Self-Leveling Epoxy Topcoat
- Colored-Sand Self-Leveling Epoxy
- Anti-Wear Textured Topcoat
- Polyurethane Super Wear-Resistant Topcoat
- Anti-Static Epoxy Topcoat
- Orange-Peel Epoxy Topcoat
- Acrylic Court Coating
- Silicon PU Stadium Coating
01. Epoxy Primer
Two-component, solvent-free epoxy primer based on Nan Ya 128 epoxy resin with imported high-solids, low-viscosity hardener and surface additives. It penetrates deeply, seals pores and bonds the concrete substrate to the coating system.
Features
- Good durability, low shrinkage
- Penetrates and seals the substrate
- Strengthens the concrete surface and gives excellent adhesion for topcoats
Applications
All common concrete substrates.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 1 h | 40 min | 20 min |
| Surface dry | 8 h | 4 h | 3 h |
| Full cure | 24 h | 10 h | 8 h |
| Property | Value |
|---|---|
| Packaging | A: 15 kg — B: 5 kg |
| Color | A: clear — B: brown |
| Mixing ratio A : B | 3 : 1 |
| Solids content | ≥ 98% (after mixing) |
Application guide
- Mixing: add components A and B at the stated ratio and mix thoroughly (machine ≥ 1 min; by hand ≥ 2 min, mixing top and bottom layers)
- Application: roller, spray or brush
- Reference consumption: 0.2 kg/m²
- Conditions: substrate moisture < 8%, relative humidity < 75%; do not apply in rain, above 80% RH or below 0°C
- Use the mixed material within 30–45 minutes
- Storage: sealed, cool and ventilated; keep away from fire, moisture and direct sunlight
02. Epoxy Intermediate Coat (tintable)
Crack-free epoxy mid-coat that can be filled with quartz sand or stone powder to raise hardness, flatness and build thickness.
Features
- Builds a thick mortar layer with high mechanical strength
- Abrasion, water, oil and chemical resistant
- Can be mixed with colored quartz sand for colored-sand floors
Applications
Light-to-medium duty plants: electronics, electrical equipment, machinery, chemicals, pharmaceuticals, textiles, garments, tobacco; warehouses, supermarkets, car parks.
Technical data (TDS)
| Property | Value |
|---|---|
| Pot life | 4 h (25°C) — 2 h (30°C) |
| Surface dry | 3 h (25°C) — 1 h (30°C) |
| Full cure | 16 h (25°C) — 12 h (30°C) |
| Mixing ratio A : B | 5 : 1 |
| Color | A: various colors — B: brown |
| Compressive strength | ≥ 30 |
Application guide
- Mixing: stir component A well (slight settling may occur in storage), then mix A and B at ratio; quartz sand or stone powder may be added
- Application: trowel or spatula; add quartz sand to reach the required thickness
- Reference consumption: 0.3–0.4 kg/m²
- Conditions: substrate moisture < 8%, relative humidity < 55%; do not apply in rain, above 85% RH or below 10°C
03. Anti-Static Epoxy Intermediate Coat
Conductive layer of anti-static floor systems, made from imported epoxy resin, conductive powder and surface additives. Low VOC with high bond strength and conductivity.
Features
- Strong, stable conductivity
- Good adhesion, fast curing
- Simple to handle and apply
Applications
Conductive layer for anti-static floors in electronics, computer rooms and areas requiring protection against electromagnetic interference.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 40 min | 25 min | 20 min |
| Surface dry | 8 h | 5 h | 4 h |
| Full cure | 12 h | 8 h | 6 h |
| Property | Value |
|---|---|
| Packaging | A: 25 kg — B: 5 kg |
| Color | A: various colors — B: brown |
| Mixing ratio A : B | 5 : 1 |
| Solids content | > 98% (after mixing) |
Application guide
- Mixing: mix A and B at ratio (machine ≥ 1 min; by hand ≥ 2 min)
- Application: over the cured primer, by trowel or roller
- Reference consumption: 0.4 kg/m²
- Conditions: relative humidity < 80%; do not apply above 85% RH, in rain or below 0°C
- Storage: sealed, cool and ventilated; keep away from fire, moisture and direct sunlight
04. Roller-Applied Epoxy Topcoat
Epoxy topcoat applied by roller or spray: low VOC, mild odor, low viscosity with good flow and adhesion — the standard build for factory and warehouse floors.
Features
- Thick, glossy film with good abrasion resistance
- Environmentally friendly, mild odor
- Good surface adhesion and high durability
Applications
Warehouses, factories, basements, car garages, hospitals, pharmaceutical and food plants — wherever dust control, surface protection and appearance matter.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 60 min | 40 min | 20 min |
| Surface dry | 8 h | 4 h | 3 h |
| Full cure | 18 h | 12 h | 8 h |
| Property | Value |
|---|---|
| Packaging | A: 16 kg — B: 4 kg |
| Color | A: optional colors — B: clear |
| Mixing ratio A : B | 4 : 1 |
| Solids content | > 90% (after mixing) |
Application guide
- Mixing: mix A and B at ratio (machine ≥ 1 min; by hand ≥ 2 min)
- Application: over the cured intermediate coat, by roller or spray
- Reference consumption: 0.2 kg/m²
- Conditions: relative humidity < 75%; avoid strong sun, prolonged rain, 80% RH or temperatures below 5°C
05. Self-Leveling Epoxy Topcoat
High-solids two-component floor material of epoxy resin, pigments and BYK additives that levels itself into a seamless, glossy surface.
Features
- Stable film: no color separation, no particles, no shade variation, no trowel marks
- High gloss, reflectance above 80%
- Smooth, flat, highly decorative surface
- Resists acids, alkalis, salts, oil and water
- Abrasion, pressure and impact resistant; high cleanliness
Applications
Garment, printing, toy and textile plants; electronics, screen-printing and paper plants; warehouses and car parks.
Technical data (TDS)
| Property | Value |
|---|---|
| Surface dry | ≤ 4 h |
| Full cure | ≤ 24 h |
| Pencil hardness | ≥ 3H |
| Film thickness | ~ 1 mm |
| Abrasion resistance (750 g/500 r) | ≤ 0.04 g |
| Water resistance | No change after 48 h |
| 10% acid / 10% NaOH | No change after 56 days |
| Gasoline / lubricant | No change after 56 days |
Application guide
- Mixing: stir component A well, then mix A and B at ratio
- Primer: standard or penetrating epoxy primer for a uniform film
- Intermediate: epoxy mid-coat mixed with quartz sand or stone powder to the required thickness
- Topcoat: spread evenly over the whole area with a notched trowel
- Reference consumption: 0.8 kg/m²
- Conditions: substrate moisture < 8%, relative humidity < 55%; do not apply in rain, above 85% RH or below 10°C
06. Colored-Sand Self-Leveling Epoxy
Self-leveling topcoat blended with colored sand, made from imported epoxy resin, wear-resistant aggregates and imported hardener. Freely combinable colors, seamless and uniform through its full thickness.
Features
- Free color combinations, premium decorative finish
- Smooth, seamless, scratch- and slip-resistant
- Withstands compression, abrasion and impact; resists acids, alkalis, oil and salt fog
- Inhibits bacteria and mold
Applications
Hotel lobbies, exhibition halls, showrooms, shopping malls and other areas needing seamless, decorative and highly hygienic floors.
Technical data (TDS)
| Property | Value |
|---|---|
| Bond strength | ≥ 2 MPa |
| Pencil hardness | ≥ 4H |
| Compressive strength | ≥ 80 MPa |
| Tensile strength | ≥ 10 MPa |
| Abrasion loss | ≤ 0.02 g |
| Surface dry | ≤ 4 h |
| Full cure | ≤ 24 h |
| 10% H₂SO₄ / engine oil (7 days) | No change |
Application guide
- Mixing: mix A and B at ratio (machine ≥ 1 min; by hand ≥ 2 min)
- Application: over the cured primer, with a trowel
- Reference consumption: 1.2–2 kg/m²
- Conditions: relative humidity < 80%; do not apply above 85% RH, in rain or below 0°C
07. Anti-Wear Textured Topcoat
Low-VOC textured topcoat with high adhesion and low viscosity, rolled to texture over the intermediate coat — for areas needing high abrasion resistance.
Features
- Dust-, moisture- and abrasion-proof; withstands pressure, acids and alkalis
- Seamless and easy to clean; mold-resistant; strong impact resistance
- High adhesion and chemical resistance
- Fast application, wide color range
Applications
Factories, warehouses and areas requiring high abrasion resistance.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 60 min | 40 min | 20 min |
| Surface dry | 8 h | 4 h | 3 h |
| Full cure | 18 h | 12 h | 8 h |
| Property | Value |
|---|---|
| Packaging | A: 24 kg — B: 6 kg |
| Color | A: optional colors — B: clear |
| Mixing ratio A : B | 4 : 1 |
| Degree of cure | > 90% (after mixing) |
Application guide
- Mixing: mix A and B at ratio (machine ≥ 2 min; by hand ≥ 3 min)
- Application: spread with a trowel over the intermediate coat, then roll to texture
- Reference consumption: 0.3–0.4 kg/m²; thickness ~1 mm
- Conditions: relative humidity < 80%; do not apply in rain, above 85% RH or below 5°C
08. Polyurethane Super Wear-Resistant Topcoat
Three-component polyurethane topcoat that protects and extends floor life, with slip resistance, abrasion resistance and durability in harsh weather.
Features
- High abrasion resistance; withstands pressure, acids and alkalis
- Seamless, easy to clean, mold- and bacteria-resistant
- High adhesion and chemical resistance
Applications
Factories, warehouses, outdoor areas and stadiums; especially suited to food processing areas and cold storage.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 60 min | 40 min | 20 min |
| Surface dry | 8 h | 4 h | 3 h |
| Full cure | 18 h | 12 h | 8 h |
| Property | Value |
|---|---|
| Packaging | A: 5 kg — B: 2 kg — C: 3 kg |
| Color | A: optional colors — B: clear — C: granite powder |
| Mixing ratio A : B : C | 5 : 2 : 3 |
| Degree of cure | > 90% (after mixing) |
Application guide
- Mixing: mix A, B and C at ratio (machine ≥ 2 min; by hand ≥ 5 min)
- Application: over an epoxy topcoat cured within 1–7 days; trowel, then roll evenly
- Reference consumption: 0.1–0.15 kg/m²
- Conditions: relative humidity < 80%; avoid rain, fog, high heat, above 85% RH or below 5°C
09. Anti-Static Epoxy Topcoat
Permanently conductive epoxy topcoat made from imported epoxy resin, wear-resistant aggregates and conductive additives; low VOC, good color retention, flow and leveling.
Features
- Durable, stable conductivity
- Hard film with abrasion and impact resistance
- Good color retention and leveling
Applications
Power plants, telecoms, microelectronics, machinery and chemical plants; production and storage of sensitive electronic components and integrated circuits.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 20 min | 15 min | 10 min |
| Surface dry | 10 h | 8 h | 6 h |
| Full cure | 24 h | 18 h | 12 h |
| Property | Value |
|---|---|
| Packaging | A: 25 kg — B: 5 kg |
| Color | A: optional colors — B: clear |
| Mixing ratio A : B | 5 : 1 |
| Degree of cure | > 98% (after mixing) |
| Electrical resistance | 1.0 × 10⁵ – 9.9 × 10⁹ Ω |
Application guide
- Mixing: mix A and B at ratio (machine ≥ 1 min; by hand ≥ 2 min)
- Application: by trowel over the fully cured intermediate coat
- Reference consumption: 0.6–0.8 kg/m² (~1 mm)
- Conditions: relative humidity < 70%; do not apply in rain, above 75% RH or below 5°C
10. Orange-Peel Epoxy Topcoat
Topcoat with an orange-peel texture that adds light slip resistance and noticeably reduces tire noise; low VOC with high adhesion.
Features
- Light slip resistance
- Decorative orange-peel effect
- Reduces tire noise
Applications
Factories, basements, walkways, plants and areas with heavy vehicle traffic.
Technical data (TDS)
| After mixing A+B | 10°C | 25°C | 35°C |
|---|---|---|---|
| Pot life | 40 min | 25 min | 20 min |
| Surface dry | 8 h | 5 h | 4 h |
| Practical dry | 12 h | 8 h | 6 h |
| Property | Value |
|---|---|
| Packaging | A: 16 kg — B: 4 kg |
| Color | A: optional colors — B: clear |
| Mixing ratio A : B | 4 : 1 |
| Degree of cure | > 90% (after mixing) |
Application guide
- Mixing: mix A and B at ratio (machine ≥ 1 min; by hand ≥ 2 min)
- Application: over the cured intermediate coat with a long-pile roller
- Reference consumption: 0.2–0.3 kg/m²
- Conditions: relative humidity < 75%; do not apply in rain, above 80% RH or below 5°C
11. Acrylic Court Coating
Water-based sports-court system with bright, UV-resistant colors that stays durable without peeling.
Features
- Water-based and non-toxic
- Bright, fade-resistant, UV-resistant colors
- High abrasion resistance; no peeling or blistering
- No moss or microbial growth
Applications
Tennis, basketball, badminton, volleyball, handball, table tennis, indoor football and other sports courts.
Application guide
- Concrete or asphalt base
- Oil-based acrylic primer
- Acrylic intermediate layer
- Acrylic texture layer
- Acrylic Court topcoat
- Court line marking
12. Silicon PU Stadium Coating
Elastic silicon PU surfacing for sports courts and playgrounds: seamless, slip-resistant and economical to install.
Features
- Seamless, slip- and abrasion-resistant
- Resists acids, alkalis, mold and water
- Many colors; easy to install and maintain
Applications
Tennis, basketball and volleyball courts; children's playgrounds and kindergartens; sidewalks, public areas and colored play areas.
Application guide
- Grind, repair and remove dust according to substrate condition
- Apply an even coat of PU Silicon binder
- Apply one or two more coats of PU Silicon to increase elasticity and wear resistance
- Apply a final PU Silicon coat for even color and no bubbling
- Mark lines to court standards
System build-up diagrams
Layer structure of each system, from substrate preparation to the finishing topcoat.
Roller-applied epoxy system
Self-leveling epoxy system
Anti-static system
Super wear-resistant system
Acrylic system
Kadier standard color chart
Kadier's 20 standard colors. On-screen colors are for reference only — final color is confirmed with a physical sample on site.
- PB04
- PB11
- PB05
- PB06
- PB07
- B01
- B04
- B05
- B02
- B03
- GY09
- G10
- Y05
- Y06
- Y07
- RP01
- G02
- G03
- YR04
- R02
Need the right product for your floor?
Send us the area, substrate condition and expected loads — Kadier's technical team will propose a system build and quote after a site survey.