Tiếng Việt
中文 (中国)
An operating plant cannot stop its whole production line just to recoat a floor, and a warehouse or showroom owner cannot close for days because one floor area needs new coating. The practical question for such buyers is not which coating systems exist in general, but where to find a supplier, how to phase the work so production and trading continue, and what to prepare so that a quotation reflects the real job. This article answers those three questions for facilities in Sa Dec ward, Dong Thap province, covering operating factories and warehouses in Sa Dec Industrial Park as well as commercial and service facilities outside the park fence. The system map for each subzone of the park is already covered in Epoxy Flooring for Sa Dec Industrial Park (Dong Thap): Refurbishing Old Floors Across Three Separate Subzones; this article does not repeat that map, and instead deals with supplier selection, phased execution and quotation preparation.
1. Sa Dec ward and Sa Dec Industrial Park: one ward, one park in three separate subzones
Sa Dec ward was formed under Resolution 1663/NQ-UBTVQH15 from the whole area and population of former wards 1, 2, 3, 4, An Hoa and Tan Quy Dong and former communes Tan Quy Tay and Tan Khanh Dong, with the new commune-level government operating from 1 July 2025. The new Dong Thap province comprises the former Dong Thap and former Tien Giang provinces under Resolution 202/2025/QH15. Stating the ward formation components at the outset matters, because the boundaries of Sa Dec Industrial Park can only be read through these former units.
Sa Dec Industrial Park is one of the operating industrial parks of Dong Thap province, planned at about 132 hectares. The park is not a single continuous site but three separate subzones, and each subzone must be named together with its former location. According to the Kadier article on Sa Dec Industrial Park and park sources, Zone C covers about 30 hectares in the former Tan Quy Dong area, the Zone C extension covers about 62 hectares in the former Tan Khanh Dong area, and part of Zone A1 covers about 40 hectares in the former An Hoa area; all three former areas now belong to Sa Dec ward. The park infrastructure investor is Dong Thap Housing and Industrial Park Development Investment Joint Stock Company (HIDICO). The general industry orientation of the park is agricultural processing, food, seafood, animal feed and light industry; this is an orientation only, not a list of tenants already in the park, and this article names no individual company.
Beyond the park fence, Sa Dec ward is also the commercial and service centre of the former Sa Dec urban area, with markets, shops, showrooms, processing, packing and storage facilities linked to agricultural trade, including the Sa Dec flower village concentrated in the former Tan Quy Dong area. The flower village appears here only as commercial context for the ward, meaning packing facilities, storage, sales points and related services, and never as a claim that flower fields themselves need industrial flooring. The location on the Tien River, with National Highway 80 and Provincial Road 848 passing through and an inland river port according to park sources, is used in this article for positioning only, not developed into a regional logistics angle. The broader picture of the provincial industrial cluster, covering Sa Dec together with Tran Quoc Toan and Tan Kieu, is available in Epoxy Flooring for the Dong Thap Industrial Cluster.
2. Finding an epoxy flooring supplier for an operating facility: four questions to ask before signing
For an operating facility, the criteria for choosing a supplier differ from those for a new plant that has not started production. A buyer should put four questions to a supplier and judge the answers in writing rather than by verbal assurance. First, how does the supplier survey an operating floor: area by area, or the whole plant in a single general pass. Second, how does the supplier phase the work so that each phase stops only one area while the remaining areas keep producing or trading. Third, what steps does the supplier take to prepare the old substrate before coating, including grinding, crack repair, treatment of oil-contaminated spots and moisture measurement. Fourth, is acceptance carried out phase by phase, or only once when the whole job is finished.
A supplier suited to Sa Dec ward is one that answers all four questions with a concrete plan for each floor area of that specific facility, rather than a generic system catalogue. A buyer should require that plan to state the order of phases, the shutdown time for each area, how traffic is rerouted and lines remarked after each phase, and the acceptance condition for each phase. If a quotation says nothing about phasing and shutdown time, that is a sign it has not yet accounted for the reality of an operating facility. The general Kadier system framework covers roller systems, self-levelling systems and the preparation steps for old concrete floors; the specific system for each area is advised only after a survey, never fixed remotely in advance and never assigned in advance by subzone.
3. Phased recoating without stopping production: a working sequence for a plant that keeps running
A phased recoating sequence for an operating plant starts by dividing the site into separate operating areas: production areas, storage areas, forklift routes and auxiliary areas. Each area is surveyed separately for deterioration, cracks, oil contamination, floor moisture and forklift loads passing over it. Phases are then ordered by the shutdown windows available for each area, for example work outside peak hours, work during a scheduled maintenance shutdown, or work when one line temporarily shifts output to another area. The order of phases is decided by available shutdown windows, not by geography and not by subzone name.
Within each phase the same sequence applies: prepare the old substrate first, by grinding the surface, repairing cracks, treating contaminated spots and checking moisture, then apply the coating, then remark lines and reroute traffic before that area returns to operation, and accept that phase before moving to the next one. Accepting each phase separately, rather than waiting until the whole job is finished, is the key point: if one phase has an adhesion or flatness defect, it is found and fixed while that area is still stopped, instead of being discovered after every area is complete. For Sa Dec Industrial Park, the fact that the three subzones are not contiguous adds an organisational requirement: each subzone is a separate worksite, so the phase plan must account for moving crews and equipment between separate locations rather than treating the whole park as one construction site.
4. Floors for commercial and service facilities outside the park: recoating while trading continues
Outside the industrial park, Sa Dec ward has a second layer of floor demand that the park article does not address: warehouses, showrooms and shops, markets and processing and packing facilities. Each type of facility has its own floor problem, but the common point is that the facility must keep trading while recoating goes on. For a warehouse, the main requirement is a floor that carries forklift loads with clearly remarked routes after recoating, and work is usually divided by racking row so that goods only have to move in part at any one time. For a showroom or shop, the main requirement is a clean, flat and easily cleaned surface, and phases are usually scheduled during the closing hours or rest days of that specific business.
For a market or a processing and packing facility, the main requirement is hygiene and resistance to moisture, oil and grease in the preparation and packing areas, and recoating there must separate wet areas from dry areas within each phase so that processing is not cross-contaminated from the area under construction. For a sales point linked to flower village trade, the requirement is a clean and easily cleaned floor in the display area and in temporary goods storage, and the work should be scheduled outside that sales point’s peak selling period. In every case the principle is the same as for a factory: divide into areas, work phase by phase, accept phase by phase, and do not close the whole facility merely because one floor area needs recoating.
5. The general Kadier supply framework and what to prepare for a realistic quotation
The general Kadier supply framework covers consultation, supply and installation through general contact channels, following this sequence: contact, survey of the floor area by area together with the shutdown windows available for each area, system advice, quotation, phased installation, then acceptance and maintenance phase by phase. This framework applies generally to every locality and is not tied to any specific location; this article does not claim that Kadier has a branch, agent, warehouse, project or client specifically in Sa Dec ward, because no per-ward presence data has been provided. A quotation is prepared after a survey, not from a ready-made price list.
To receive a realistic quotation from the first survey, a buyer should prepare six groups of information before contacting a supplier. First, the area of each floor zone, measured separately for each zone rather than only as a total for the whole facility. Second, the condition of the floor in each zone: peeling, cracks, oil contamination, moisture, and the locations of the worst damaged spots. Third, forklift loads and traffic volumes on each zone. Fourth, hygiene and chemical resistance requirements for the industry of the facility. Fifth, the shutdown windows available for each zone, including daily stop hours and any longer shutdown period. Sixth, photographs and video of the current floor condition, showing each damaged zone clearly. A quotation enquiry that includes all six groups allows a supplier to build a phase plan and a quotation close to the real scope of work, instead of a general quotation that must be revised repeatedly after the survey.
6. Contact for consultation and quotations
For system advice, an area-by-area floor survey and a quotation after survey for a facility in Sa Dec ward, contact Kadier by Hotline and Zalo on 0899355489 or by WeChat on wxid_95o54joujyrr12. When contacting, a buyer should send the area of each zone, the floor condition, forklift loads, hygiene and chemical resistance requirements, the shutdown windows available for each zone and photographs of the current condition, so that the first survey already has enough information to build a phased recoating plan.
